Skip to content

OPNsense Gateway Cutover — Execution Checklist

Date: 2026-02-21 Window: 30 minutes max Rollback time: ~2 minutes Alternative internet: Phone tethering (safety net only)

Before You Start

  • [ ] Open Proxmox web UI: https://192.168.0.237:8006
  • [ ] Open this file on your phone (in case Mac loses connectivity)
  • [ ] Have an Ethernet cable ready for nic1
  • [ ] Announce: "Internet will be down for up to 30 minutes"
  • [ ] Note current time: __

Step 1: Connect nic1 to Switch

Physical:Plug an Ethernet cable from Proxmoxnic1 (2nd port) into the MokerLink switch.

Verify from Mac terminal:

ssh augusto@192.168.0.237 "ip link show nic1 | grep 'state UP'"

Expected: state UP

  • [ ] nic1 shows UP

Step 2: Apply Proxmox Network Config

This moves management IP from vmbr0 → vmbr1 (now on the switch via nic1).

ssh augusto@192.168.0.237 "sudo cp /etc/network/interfaces.cutover /etc/network/interfaces && sudo cp /etc/network/interfaces.d/vmbr1.cutover /etc/network/interfaces.d/vmbr1 && sudo ifreload -a"

Verify:

ssh augusto@192.168.0.237 "ip -br addr show vmbr0 && ip -br addr show vmbr1"

Expected:

  • vmbr0 — no IP (manual)

  • vmbr1 — 192.168.0.237/24

  • [ ] vmbr0 has no IP

  • [ ] vmbr1 has 192.168.0.237/24
  • [ ] Proxmox web UI still works at https://192.168.0.237:8006

Step 3: Swap Cables

Physical — two cable changes

  1. Unplug ISP Ethernet from TP-Link WAN port→ plug intoProxmox nic0
  2. Unplug the old switch cable from Proxmox nic0 (no longer needed)

Result: nic0 faces ISP modem, nic1 faces switch.

Internet is now DOWN for everyone. Clock is ticking.

  • [ ] ISP cable in Proxmox nic0
  • [ ] Old switch cable removed from nic0

Step 4: Verify OPNsense Gets Public IP

Open Proxmox web UI→ VM 100 (OPNsense) →Console.

In the OPNsense console (or web UI from the console browser):

  • Dashboard → Interfaces → WAN → should show a public IP via DHCP

If no public IP: wait 30 seconds, then run in OPNsense console:

/usr/local/sbin/configctl interface reconfigure wan
  • [ ] OPNsense WAN has a public IP

If no public IP after 2 minutes → ROLLBACK (see bottom of this file)

From Mac (still connected to WiFi):

  1. Open http://192.168.0.1 (TP-Link admin)
  2. Operation Mode → Access Point
  3. Set static IP: 192.168.0.2
  4. Apply (TP-Link reboots, ~1 minute)
  5. After reboot: move TP-Link cable from WAN portto aLAN port on the switch

WiFi will briefly drop and reconnect. Same SSID/password = auto-reconnect.

  • [ ] TP-Link in AP mode
  • [ ] TP-Link cable: LAN port → switch (NOT WAN port)
  • [ ] Mac reconnected to WiFi

Step 6: Configure OPNsense LAN

From Proxmox web UI→ VM 100 (OPNsense) →Console:

Open OPNsense web UI inside the console (https://192.168.1.1):

6a. Change LAN IP

  • Interfaces → LAN
  • IPv4: 192.168.0.1/24
  • Save → Apply

6b. Enable DHCP

  • Services → DHCPv4 → LAN
  • Enable: checked
  • Range: 192.168.0.100 – 192.168.0.250
  • DNS server: 192.168.0.10
  • Gateway: 192.168.0.1
  • Save

6c. Add Static Mappings

  • Docker VM: MAC BC:24:11:A8:E9:C5 → 192.168.0.10
  • TP-Link AP: (get MAC from lease list) → 192.168.0.2
  • Save → Apply

After applying, OPNsense LAN is at 192.168.0.1. Proxmox gateway now works.

  • [ ] LAN IP changed to 192.168.0.1
  • [ ] DHCP enabled (range .100–.250, DNS .10, gateway .1)
  • [ ] Docker VM static mapping added

Step 7: Re-IP Docker VM

Docker VM's gateway (192.168.1.1) is gone. Fix from Proxmox:

ssh augusto@192.168.0.237 "sudo qm guest exec 101 -- bash -c 'ip addr del 192.168.1.10/24 dev ens18; ip addr add 192.168.0.10/24 dev ens18; ip route add default via 192.168.0.1'"

If qm guest exec fails, use Proxmox web UI → VM 101 → Console, then:

sudo ip addr del 192.168.1.10/24 dev ens18
sudo ip addr add 192.168.0.10/24 dev ens18
sudo ip route add default via 192.168.0.1

Make it persistent:

ssh augusto@192.168.0.237 "sudo qm guest exec 101 -- bash -c \"sed -i 's/192.168.1.10/192.168.0.10/g; s/gateway 192.168.1.1/gateway 192.168.0.1/g' /etc/network/interfaces\""

Or edit via Proxmox console if sed doesn't work.

Verify:

ssh augusto@192.168.0.10 "ip addr show ens18 | grep inet && ping -c1 8.8.8.8"
  • [ ] Docker VM at 192.168.0.10
  • [ ] Docker VM has internet (ping 8.8.8.8)

Step 8: Verify — The Family Test

Internet

  • [ ] Reconnect phone WiFi → gets 192.168.0.x IP
  • [ ] Phone can browse the web
  • [ ] Netflix works on TV (the real test)

Homelab

  • [ ] SSH to Docker VM: ssh docker-vm (Tailscale) or ssh <augusto@192.168.0.10>
  • [ ] Pi-hole resolving: ssh <augusto@192.168.0.10> "docker exec pihole dig google.com @127.0.0.1 +short"
  • [ ] Vaultwarden accessible
  • [ ] Proxmox web UI: https://192.168.0.237:8006
  • [ ] OPNsense web UI: https://192.168.0.1 (from Mac)
  • [ ] Tailscale: tailscale status

Announce: "Internet is back!"

  • [ ] Note completion time: __

Rollback (If Anything Goes Wrong)

Before step 6 (OPNsense LAN still 192.168.1.x)

# 1. Revert Proxmox config
ssh augusto@192.168.0.237 "sudo cp /etc/network/interfaces.original /etc/network/interfaces && sudo cp /etc/network/interfaces.d/vmbr1.original /etc/network/interfaces.d/vmbr1 && sudo ifreload -a"

# 2. Physical: ISP cable back to TP-Link WAN, switch cable back to Proxmox nic0, unplug nic1
# 3. TP-Link: reboot to restore router mode (if AP mode was applied)

After step 6 (OPNsense LAN already at 192.168.0.x)

  1. OPNsense console: Interfaces → LAN → change back to 192.168.1.1/24, Apply
  2. Docker VM: ip addr del 192.168.0.10/24 dev ens18; ip addr add 192.168.1.10/24 dev ens18; ip route add default via 192.168.1.1
  3. Then do the cable/config revert above

Nuclear option

Connect Mac to phone tethering, SSH to VPS, figure it out from there.